|
 |
|
|
Dual Channel, 60 Watt Acoustic Combo
The Bronzewood 60 was specifically designed to get the very best
from your electro-acoustic instruments, while integrating a dedicated
microphone channel. The Guitar channel features an adjustable compressor,
reverb, active three-band EQ with semi-parametric sweepable mids
and SansAmp tube/mic emulation circuitry to remove the harsh harmonics
from piezo pickups. The Mic channel has switchable phantom power
for condenser microphones, active EQ and mixable reverb. From the
Elvis-cool crocodile vinyl covering to the sweet open tone, this
is the last word in amps for any acoustic player headed for the
stage or studio.
|
Guitar
Channel |
|
Mic
Channel |
| Compressor,
ranging from 1:1 to 5:1 |
XLR
mic level female input |
| Phase
switch |
24V
phantom switch to power a condenser microphone (or any other
phantom powerable product, perhaps a SansAmp Acoustic DI?) |
| Preamp
control |
3-band
active EQ controls |
| Notch
filter |
Reverb
Mix to control the balance of reverb between the Guitar and
Mic channels |
| Mid
Shift and Mid are sweepable, semi-parametric EQ controls and
range from 170Hz to 3kHz, ±16dB, respectively |
|
| Active
tone controls, boost or cut ±12dB |
Unique
Blend control enables you to determine the ratio of direct
instrument signal and SansAmp Tube/Microphone Emulation circuitry |
| Full-length,
6-spring Accutronics® reverb |
|
Click to enlarge |
| BW60
ADDITIONAL FEATURES |
Special
design 12” speaker and high frequency horn.
Mid
Shift and Mid EQ controls range from 170Hz to 3kHz, ±16dB
respectively.
SansAmp
XLR Direct Out for stage and studio applications allows you
to go direct to any mixing console. For live gigs, you can run
directly into the P.A. system. In larger venues, you’ll
be able to utilize the P.A. monitors to supplement your stage
volume.
Full
length, 6-spring reverb.
A Reverb Mix controls the balance of reverb between the Guitar
and Mic channels.
Headphone
output, which can also be used as a 1/4” direct out.
Effect
Loop.
Footswitch
jack that accepts any alternating footswitch to control the
Reverb function. An optional
factory footswitch is available.
|
| SPECIFICATIONS |
| Model
Number: |
BW60 |
| Input
Impedance: |
(Guitar): 4.7M Ohms
(Mic): 3.3k Ohms |
| Nominal
Input Level: |
-20dBu |
| Optimal
Output Load: |
8 Ohms |
| Power
Output: |
60W |
| Effect
Loop Input Impedance |
1MOhm |
| Maximum
Effect Loop Input |
approx.
-10dBm |
| Nominal
Effect Loop Output Impedance |
1KOhm |
| Nominal
Effect Loop Output |
approx.
-10dBu |
| Effect
Loop Output Level* |
0
to -10dBu |
| Maximum
Power Consumption: |
120W |
| AC
Input Power: |
(Factory
set): 100V, 117V, 220V, 230V, 240V |
| NOTE:
AC power cannot be switched. See authorized dealer/distributor
for voltage modification information. |
| Cycles: |
50/60 Hz |
| Speaker: |
Model
#2112-A, Special design 12" / 100W - 8 Ohms |
| Horn: |
Model #2125-H, Special design / 60W - 8 Ohms |
| Dimensions: |
20"w x 17"h x 11"d |
| Weight: |
38 lbs |
Note: With on-going product development and improvements, specifications
and/or the cosmetic appearance of this unit may change without
prior notice. Replacement parts are available, i.e., knobs,
logo plate, handles, etc. For more information, please contact
your authorized dealer or Tech 21. |
|
| |
|
 |
